Go back to datasheets

VICTREX™ PEEK POLYMER AS110

High performance thermoplastic material, reinforced PolyEtherEtherKetone (PEEK), semi crystalline, granules for injection moulding, easy flow, colour natural/beige.

VICTREX™ AS110 is typically used in applications that operate across a wide temperature range and require a combination of strength and ductility, good creep resistance and chemical resistance in aggressive fluid environments. Less abrasive on low-hardened light alloys compared to stiffer wear grades.

Material Properties
Physical

Nominal Value

Unit

Test Method

Density (Crystalline)

1.41

g/cm³

ISO 1183

Spiral Flow 1

16.0

cm

Internal Method

Molding Shrinkage 2

ISO 294-4

Across Flow

1.1

%

Flow

0.90

%

Mechanical

Nominal Value

Unit

Test Method

Tensile Modulus (23°C)

4700

MPa

ISO 527-1

Tensile Stress (Break, 23°C)

75.0

MPa

ISO 527-2

Tensile Strain (Break, 23°C)

10

%

ISO 527-2

Flexural Modulus (23°C)

4700

MPa

ISO 178

Flexural Stress (23°C)

140

MPa

ISO 178

Compressive Stress (23°C)

130

MPa

ISO 604
Impact

Nominal Value

Unit

Test Method

Notched Izod Impact Strength (23°C)

5.5

kJ/m²

ISO 180/A

Unnotched Izod Impact Strength (23°C)

20.0

kJ/m²

ISO 180
Hardness

Nominal Value

Unit

Test Method

Shore Hardness (Shore D, 23°C)

85.0

ISO 868
Thermal

Nominal Value

Unit

Test Method

Deflection Temperature Under Load (1.8 MPa, Unannealed)

155

°C

ISO 75-2/Af

Glass Transition Temperature

ISO 11357-2

Onset

143

°C

Midpoint

147

°C

Melting Temperature

343

°C

ISO 11357-3

CLTE - Flow

ISO 11359-2

< 143°C

45

ppm/K

> 143°C

120

ppm/K

CLTE - Average

ISO 11359-2

< 143°C

50

ppm/K

> 143°C

120

ppm/K

Thermal Conductivity

ISO 22007-4

23°C 3

0.30

W/m/K

23°C 4

0.32

W/m/K

Fill Analysis

Nominal Value

Unit

Test Method

Melt Viscosity (400°C)

225

Pa·s

ISO 11443
Typical Processing Information
Injection

Nominal Value

Unit

Drying Temperature

120 to 150

°C

Drying Time

3.0 to 5.0

hr

Hopper Temperature

< 100

°C

Rear Temperature

360

°C

Middle Temperature

360 to 365

°C

Front Temperature

370

°C

Nozzle Temperature

375

°C

Mould Temperature

170 to 200

°C

Injection Notes

Runner: Die / nozzle >3mm, manifold >3.5mm
Gate: >2mm or 0.5 x part thickness

Important notes:
1) Processing conditions quoted in our datasheets are typical of those used in our processing laboratories

  • Data for mould shrinkage should be used for material comparison. Actual mould shrinkage values are highly dependent on part geometry, mould configuration, and processing conditions.
  • Mould shrinkage differs for along flow and across flow directions. “Along flow” direction is taken as the direction the molten material is travelling when it exits the gate and enters the mould.
  • Mould shrinkage is expressed as a percent change in dimension of a specimen in relation to mould dimensions.

2) Data are generated in accordance with prevailing national, international and internal standards, and should be used for material comparison. Actual property values are highly dependent on part geometry, mould configuration and processing conditions. Properties may also differ for along flow and across flow directions.

Detailed data available on our website www.victrex.com or upon request.

Notes
1Mould Temperature: 180°C, Melt Temperature: 375°C, 1.00 mm
2375°C nozzle, 180°C tool
3Along flow
4Average

Hi, do you have PEEK questions I can help with?

Vic
Loading...