빅트렉스 ST 45GL30

High performance thermoplastic material, 30% glass fibre reinforced PolyEtherKetoneEtherKetoneKetone (PEKEKK), semi crystalline, granules for injection moulding, standard flow, colour natural/beige.

Applications for higher strength and stiffness at elevated temperatures. Low coefficient of thermal expansion. Chemically resistant to aggressive environments.

Material Properties
Physical	Nominal Value	Unit	Test Method
Density (Crystalline)	1.53	g/cm³	ISO 1183
Spiral Flow			Internal Method
--¹	10.0	cm
--²	44.0	cm
Molding Shrinkage³			ISO 294-4
Across Flow	0.90	%
Flow	0.30	%
Water Absorption Saturation (100°C)	0.60	%	ISO 62
Mechanical	Nominal Value	Unit	Test Method
Tensile Modulus (23°C)	12000	MPa	ISO 527-1
Tensile Stress			ISO 527-2
Break, 23°C	188	MPa
Break, 125°C	130	MPa
Break, 175°C	80.0	MPa
Break, 275°C	50.0	MPa
Tensile Strain (Break, 23°C)	2.6	%	ISO 527-2
Flexural Modulus (23°C)	11000	MPa	ISO 178
Flexural Stress			ISO 178
23°C	280	MPa
125°C	180	MPa
175°C	120	MPa
275°C	70.0	MPa
Compressive Stress			ISO 604
23°C	290	MPa
120°C	190	MPa
200°C	75.0	MPa
250°C	50.0	MPa
Impact	Nominal Value	Unit	Test Method
Charpy Notched Impact Strength (23°C)	9.0	kJ/m²	ISO 179/1eA
Charpy Unnotched Impact Strength (23°C)	70.0	kJ/m²	ISO 179/1U
Notched Izod Impact Strength (23°C)	9.2	kJ/m²	ISO 180/A
Unnotched Izod Impact Strength (23°C)	60.0	kJ/m²	ISO 180
Thermal	Nominal Value	Unit	Test Method
Deflection Temperature Under Load (1.8 MPa, Unannealed)	380	°C	ISO 75-2/Af
Glass Transition Temperature			ISO 11357-2
Onset	162	°C
Midpoint	169	°C
Melting Temperature	387	°C	ISO 11357-3
CLTE - Flow			ISO 11359-2
< 162°C	21	ppm/K
> 162°C	23	ppm/K
CLTE - Average			ISO 11359-2
< 162°C	40	ppm/K
> 162°C	100	ppm/K
Thermal Conductivity			ISO 22007-4
23°C⁴	0.30	W/m/K
23°C⁵	0.35	W/m/K
Electrical	Nominal Value	Unit	Test Method
Volume Resistivity (23°C)	1.0E+16	ohms·cm	IEC 60093
Dielectric Strength (2.00 mm)	22.0	kV/mm	IEC 60243-1
Dielectric Constant (23°C, 1 kHz)	3.30		IEC 60250
Dissipation Factor (23°C, 1 MHz)	4.0E-3		IEC 60250
Comparative Tracking Index	150	V	IEC 60112
Fill Analysis	Nominal Value	Unit	Test Method
Melt Viscosity (420°C)	600	Pa·s	ISO 11443

Typical Processing Information
Injection	Nominal Value	Unit
Drying Temperature	150 to 180	°C
Drying Time	3.0 to 6.0	hr
Suggested Max Moisture	0.020	%
Hopper Temperature	< 100	°C
Rear Temperature	385	°C
Middle Temperature	395 to 400	°C
Front Temperature	405	°C
Nozzle Temperature	410	°C
Mould Temperature	200 to 220	°C
Injection Notes
Drying Temperature / Time: 180°C / 3h or 150°C / 6h (residual moisture <0.02%) Runner: Die / nozzle >3mm, manifold >3.5mm Gate: >2mm or 0.5 x part thickness Important notes: 1) Processing conditions quoted in our datasheets are typical of those used in our processing laboratories Data for mould shrinkage should be used for material comparison. Actual mould shrinkage values are highly dependent on part geometry, mould configuration, and processing conditions. Mould shrinkage differs for along flow and across flow directions. “Along flow” direction is taken as the direction the molten material is travelling when it exits the gate and enters the mould. Mould shrinkage is expressed as a percent change in dimension of a specimen in relation to mould dimensions. 2) Data are generated in accordance with prevailing national, international and internal standards, and should be used for material comparison. Actual property values are highly dependent on part geometry, mould configuration and processing conditions. Properties may also differ for along flow and across flow directions. Detailed data available on our website www.victrex.com or upon request.

Notes

¹Mould Temperature: 210°C, Melt Temperature: 410°C, 1.00 mm

²Mould Temperature: 210°C, Melt Temperature: 410°C, 3.00 mm

³410°C nozzle, 210°C tool

⁴Average

⁵Along flow